Shielded Metal Arc Welder Course (SMAW Fillet Welding) in South Africa
The Shielded Metal Arc Welder course (a QCTO fillet welder skills programme) prepares you to produce fillet welds with the shielded metal arc welding (SMAW) process, often called stick welding, on carbon steel and stainless steel in the flat, horizontal, vertical and overhead positions. You learn welding safety, joints and welds, weld imperfections, arc welding and electrical basics, then practise single-pass and multi-pass fillet welds, including fitting and tacking, to the standards the curriculum names.
It is a QCTO skills programme at NQF Level 2 with 40 credits (12 knowledge, 12 practical, 16 work experience). It follows the same module structure as the SAQA-registered Occupational Certificate: Welder and is aimed at people who weld gates, burglar bars and other fillet welds in a factory or production setting. This SMAW welding course is delivered from Wheelset Academy's Pretoria and Kempton Park branches.
Share your details to access the brochure
What the Shielded Metal Arc Welder course covers
The 40-credit skills programme is built from six knowledge modules (12 credits), one practical skill module (12 credits) and one work experience module (16 credits).
Knowledge modules · 12 credits
Six modules from the welder qualification
- Introduction to the welding trade: welder profiles, apprenticeships and the trade test (2 credits)
- Occupational safety, health and environmental protection, including fumes, confined spaces, gases, earthing and fire fighting (4 credits)
- Welding schematics, calculations, welds and welded joints: leg length, throat thickness and joint preparation (2 credits)
- Weld imperfections: causes, remedies and the effect on fatigue life (2 credits)
- Fusion welding and consumables (1 credit)
- Arc welding: electricity, power sources, polarity, slag and flux, hazards and PPE (1 credit)
Practical skill module · 12 credits
Perform fillet welds using the SMAW process
- Perform a single-pass fillet weld on plate in the flat (1F), horizontal (2F), vertical up (3F) and overhead (4F) positions, including fitting and tacking
- Perform a multi-pass fillet weld in the same four positions, including fit-up, tack and inter-pass cleaning
- Use root, filler and cap welding techniques
- Prepare material, set up equipment and check your welds visually against quality indicators
Work experience module · 16 credits
Produce a range of fillet welds
- Assist an experienced welder with fillet welding for a minimum of two days
- Fillet weld ferrous or non-ferrous materials in a range of production situations
- Achieve the coded status or required standard
Assessment is facilitated and quality-assured by the QCTO. Recognition of Prior Learning (RPL) is available for learners who can show the required competencies.
Fillet welds in all four positions, single pass and multi pass
Most short welding courses teach flat welding only. This programme requires fillet welds in the flat, horizontal, vertical-up and overhead positions, first as a single pass and then as a multi-pass weld with a root, filler and cap, each assessed against international standards the curriculum names.
Single-pass fillet welds
Fit up, tack and weld a T-joint in each position, then inspect it for imperfections and correct what you find.
Multi-pass fillet welds
Build larger fillet welds with root, filler and cap passes, with cleaning between passes and correct equipment settings.
Safe, quality work
Follow health, safety and environmental practice, adjust equipment for the job and explain the cause and prevention of the defects you see.
Real SMAW fillet welding, not just theory
- Set up a welding machine and select the correct settings for the job
- Prepare and clean material and fit up joints
- Tack weld components in position
- Lay single-pass fillet welds in the flat and horizontal positions
- Lay single-pass fillet welds in the vertical-up and overhead positions
- Lay multi-pass fillet welds with root, filler and cap runs
- Clean and dress welds and clean between passes
- Identify leg length, throat thickness, penetration and number of runs from a sketch
- Inspect welds visually and recognise gas pores, lack of fusion, incomplete penetration and cracks
- Explain how to prevent and rectify weld defects
- Use PPE, ventilation and fire precautions around arc welding
- Assist an experienced welder with fillet welding in a workplace
Shielded metal arc welder course duration, entry requirements, cost and certificate
The questions learners ask most before enrolling in a stick welding course, answered from the curriculum and checked against what other providers publish.
Course duration
The curriculum sets 40 credits, which at the standard 10 notional hours per credit is about 400 hours of learning, including 16 credits of work experience. Providers list anything from a four-week short course to three to six months. Wheelset Academy will confirm its schedule with admissions.
Entry requirements
The curriculum assumes learning at NQF Level 1. Providers also ask for a Grade 7 to 9 education with basic literacy and numeracy, a minimum age of 16, a certified ID copy and proof of residence, so ask admissions which documents we need. Ask about Recognition of Prior Learning (RPL) if you already weld.
Course cost
Our current fee is on the fees page. Providers publish prices from about R6,000 for a four-week short course to monthly instalments of R15,000 on one skills programme guide, and many give no price at all, so compare what each price includes: assessment, consumables, PPE and workshop time.
Certificate
On success you receive a QCTO skills programme certificate after the programme assessment. Some short courses issue a provider certificate or a semi-skilled arc welding certificate, which is a different product, so check what your certificate is and who issues it.
Shielded metal arc welder skills programme, short stick welding course or full Welder qualification?
Several different products share the stick welding and SMAW name. They are not interchangeable, so check the level, credits and code before you pay.
This programme: fillet welder, NQF 2
Shielded Metal Arc Fillet Welder skills programme, curriculum code 651202-000-00-SP01, NQF Level 2, 40 credits. Several providers list it as SP-191208, so confirm the Skills Programme ID with admissions.
Short stick welding courses
One- to four-week courses, sometimes built on an older unit standard such as SAQA 243056, Weld carbon steel workpieces using the SMAW process in all positions (NQF Level 2, 16 credits per one provider). They issue a provider certificate, not a QCTO skills programme certificate.
Coded Welding programme (SP-210402)
Wheelset Academy's separate NQF Level 4 programme with 96 credits. It goes beyond fillet welds. See the Coded Welding course page.
Occupational Certificate: Welder
The full SAQA 94100 qualification at NQF Level 4 with 373 credits, covering SMAW, GMAW and GTAW. A trade test is a further route, usually after workplace experience.
Who should take the Shielded Metal Arc Welder course
Is this programme right for you?
- You want an entry-level welding qualification with a registered credit value
- You work as a welder’s assistant or fabrication assistant and want recognised skills
- You weld, or want to weld, gates, burglar bars and production fillet welds
- You want a first step toward the full Welder qualification, a trade test or a boilermaker route
- You are a school leaver or career changer with NQF Level 1 learning
By the end you will be able to
- Set up and adjust an arc welding machine for the job
- Prepare, fit up and tack joints
- Lay single-pass and multi-pass fillet welds in positions 1F to 4F
- Use root, filler and cap techniques and clean between passes
- Inspect welds visually and name the cause of common defects
- Work safely with fumes, gases, earthing, PPE and fire precautions
Training methodology: how the stick welding course is delivered, assessed and certified
Knowledge is taught in class and practical welding takes place in a workshop under supervision.
Delivery
The curriculum requires an approved SMAW procedure, equipment and consumables, and a facilitator-to-learner ratio of 1 to 12 in practical sessions, with a workshop assistant for every 4 learners.
Assessment
You are assessed on the knowledge modules, on practical fillet welds in each position and on workplace evidence from the work experience module. The QCTO facilitates assessment and quality assurance.
Certificate
After the programme assessment the QCTO issues the skills programme certificate. Learners with prior welding experience can ask about RPL.
Why train your welders on this skills programme
Fillet welds make up much of everyday fabrication, from gates and burglar bars to production work. A registered QCTO skills programme gives each learner defined, assessed outcomes, workplace evidence and a credit-bearing certificate, which supports your skills development records. Some providers mention B-BBEE skills development spend and the Section 12H allowance as funding routes, so ask your skills development facilitator or tax adviser what applies to you. Group intakes can be arranged by contacting admissions.
Benefits of the QCTO Shielded Metal Arc Welder skills programme
Recognised and credit-bearing
A QCTO skills programme at NQF Level 2 with 40 credits, not just a certificate of attendance.
All four positions
Fillet welds in the flat, horizontal, vertical-up and overhead positions, single pass and multi pass.
A route to progression
It follows the module structure of the Welder qualification, so it is a first step toward further welding programmes.
Fillet welder skills programme vs. the full Welder qualification
This programme is a focused slice of the Occupational Certificate: Welder (SAQA ID 94100). Use this to see where it sits and how it differs from a short stick welding course.
| Consideration | Shielded Metal Arc Fillet Welder | Occupational Certificate: Welder (SAQA 94100) |
|---|---|---|
| Level and credits | NQF Level 2, 40 credits | NQF Level 4, 373 credits |
| Processes | SMAW only | SMAW, GMAW and GTAW |
| Weld types | Fillet welds in all four positions | Fillet, plate butt and pipe welds |
| Materials | Carbon steel and stainless steel | A wider range of metals and consumables |
| Work experience | 16 credits of fillet welding | 152 credits across fillet, plate, pipe and cutting |
| Best suited to | People who need recognised fillet welding skills for gates, burglar bars and production work, or a first step toward the full qualification | Learners aiming for artisan-level welding across processes |
If you're not sure which fits your situation, contact admissions before applying — see the contact details below.
Verify this programme yourself
Page information reviewed: 25 October 2026.
Curriculum 651202-000-00-SP01
This is a QCTO skills programme, identified by its curriculum code (651202-000-00-SP01) and linked to the SAQA-registered Occupational Certificate: Welder, SAQA ID 94100. The SAQA record shows that qualification as reregistered with a registration end date of 30 December 2025, a last enrolment date of 30 December 2026 and a last achievement date of 30 December 2029. The curriculum itself dates from 29 May 2019 and cites different SAQA figures (ID 91400, 372 credits), so confirm the programme's current status directly with SAQA and the QCTO and confirm Wheelset Academy's accreditation scope before you pay.
The curriculum requires providers to meet the Occupational Health and Safety Act, to show access to an approved SMAW procedure, equipment and consumables, and to keep a facilitator-to-learner ratio of 1 to 12 in practical sessions with a workshop assistant for every 4 learners. Providers list this programme as SP-191208, a code that does not appear in the curriculum document, so confirm the Skills Programme ID with admissions.
Check QCTO accreditation · SAQA · Wheelset Academy accreditations page
Shielded metal arc welder career opportunities
The programme is linked to the occupation Welder (651202). The curriculum states that a graduate can weld gates, burglar bars and the fillet welds needed in a factory or production environment. The related welding pathways in the curriculum include:
- Fillet Welder
- Production Welder
- Gate and Burglar Bar Fabricator
- Factory Welder
- Coded Welder
- Plate and Butt Welder
- Pipe Welder
- Welder's Assistant
- Fabrication Assistant
- Arc Welder
For further study, the curriculum lists the Gas Tungsten Arc and Gas Metal Arc fillet welding skills programmes, and plate/butt and pipe welding programmes. Wheelset Academy also offers a full Coded Welding programme and the Welder qualification. Confirm progression options with admissions.
Job titles vary by employer and experience. A skills programme supports career preparation but does not guarantee a specific title, salary or appointment.
Shielded Metal Arc Welder course FAQs
What is the Shielded Metal Arc Welder course?
It is a QCTO skills programme at NQF Level 2 with 40 credits that prepares you to produce SMAW fillet welds on carbon steel and stainless steel in the flat, horizontal, vertical and overhead positions.
What is shielded metal arc welding?
Shielded metal arc welding (SMAW), also called stick or manual metal arc welding, uses a flux-covered electrode that creates the arc and a protective shield of gas and slag.
What are the entry requirements?
The curriculum assumes learning at NQF Level 1. Confirm any additional requirements with admissions, and ask about Recognition of Prior Learning (RPL) if you have welding experience.
How many credits does the programme carry, and how long does it take?
40 credits in total: 12 knowledge, 12 practical and 16 work experience. Wheelset Academy has not published a fixed programme duration yet, so confirm the intake structure with admissions. The work experience includes at least two days assisting an experienced welder.
What fillet welds will I make?
Single-pass and multi-pass fillet welds in the flat (1F), horizontal (2F), vertical-up (3F) and overhead (4F) positions, including fitting and tacking, with root, filler and cap techniques for multi-pass welds.
Does the course cover MIG or TIG welding?
No. This programme covers SMAW only. MIG and TIG are covered by other programmes and by the full Welder qualification.
Is this the same as the Coded Welding course?
No. Wheelset Academy's Coded Welding programme is SP-210402 at NQF Level 4 with 96 credits. This is a shorter, fillet-only programme at NQF Level 2 with 40 credits.
Is this the full Welder qualification?
No. The full Occupational Certificate: Welder is SAQA ID 94100 at NQF Level 4 with 373 credits. This skills programme draws on the same modules for fillet welding with SMAW only.
What can I weld after the course?
The curriculum says you can weld gates, burglar bars and the fillet welds required in a factory or production environment.
Who quality-assures this programme?
The curriculum states that the QCTO facilitates the assessment and quality assurance. Confirm Wheelset Academy's accreditation scope with admissions or the QCTO before enrolling.
What is the difference between this and a short stick welding course?
Short courses run for days or weeks and usually issue a provider certificate. This is a 40-credit QCTO skills programme with knowledge, practical and work experience modules. Compare the credit value and the certificate issuer before you pay.
What is the programme ID, SP-191208?
Several providers list this programme as SP-191208. The curriculum document gives code 651202-000-00-SP01 and does not print an SP number, so confirm the Skills Programme ID with admissions or the QCTO.
How much does a stick welding course cost?
Wheelset Academy's current fees are on the fees page. Other providers publish prices from about R6,000 for a four-week short course to monthly instalments on a skills programme, and many publish none, so compare what each price includes.
What electrodes and welding positions will I learn?
The curriculum covers fillet welds in positions 1F, 2F, 3F and 4F using SMAW. Short courses elsewhere mention electrode types such as E6010, E6013 and E7018, but this page does not claim a specific electrode list because the curriculum does not state one.
Is there work experience in the programme?
Yes. The work experience module carries 16 credits and includes at least two days assisting an experienced welder with fillet welding.
Can I become a boilermaker or take a trade test after this?
This programme is an entry step. Boilermaker and trade test routes need further learning and workplace experience, so ask admissions about progression.
Is this the same as stick welding, arc welding or MMA?
Shielded metal arc welding is also called stick welding and manual metal arc (MMA) welding. Arc welding is a broader term that can cover other processes.
What PPE do I need?
The curriculum covers PPE, ventilation and fire precautions as part of safety. Ask admissions whether you must bring your own PPE, because some providers require it.
How do I apply?
Review the current fees and intake information, then submit your application through Wheelset Academy's online application page. Admissions can confirm the programme duration, check your documents and confirm accreditation scope before registration is finalised.
Ready to start your welding career with stick welding?
Apply for the Shielded Metal Arc Welder course, or compare it with Wheelset Academy's Coded Welding and Welder qualifications first.
Programme information reviewed: 25 October 2026. The programme identifier, curriculum code, NQF level, credit values and entry requirement above reflect the QCTO curriculum document. The curriculum and SAQA record differ on some figures, and this page uses the SAQA record for the parent qualification. No SAQA ID is claimed for the skills programme itself. The duration is not yet confirmed. Fees, intakes, delivery mode and accreditation scope can change and should be confirmed with Wheelset Academy before enrolment.